| 1. |
- Baroni, Mpma, et al.
(author)
-
Modeling and gradient pattern analysis of irregular SFM structures of porous silicon
- 2006
-
In: Microelectronics Journal. - : Elsevier BV. - 0026-2692. ; 37:4, s. 290-294
-
Journal article (peer-reviewed)abstract
- Technological applications in opto-electronic devices have increased the interest in characterizing porous silicon structure patterns. Due to its physical properties, solutions from KPZ 2D are adopted to simulate the structure of porous material interface whose spatial characteristics are equivalent to those found in porous silicon samples. The analysis of the simulated and real scanning Force Microscopy (SFM) surfaces was done using the Gradient Pattern Analysis (GPA). We found that the KPZ 2D model presented asymmetry levels compatible with the irregular surfaces observed by means of SFM images of pi-Si.
|
|
| 2. |
- Baroni, M. P. M. A., et al.
(author)
-
Optical and morphological properties of porous diamond-like-carbon films deposited by magnetron sputtering
- 2006
-
In: Journal of Non-Crystalline Solids. - : Elsevier BV. - 0022-3093 .- 1873-4812. ; 352:32-35, s. 3734-3738
-
Journal article (peer-reviewed)abstract
- Porous diamond-like-carbon (PDLC) thin films obtained on silicon substrate by DC low energy magnetron sputtering have been investigated by photoluminescence, transmission and reflection spectroscopy, photoacoustic and spectroscopic ellipsometry. The absorption features observed for these films show similarities with those of porous silicon (PS) as well as in the performed gradient structural pattern classification of the SFM porosity, by means of the computational GPA-flyby environment on PS and PDLC samples. The dielectric function is also calculated for the bulk diamond-like carbon using the full-potential linearized augmented plane wave method within the framework of local density approximation to density functional theory. From the measurement a low real dielectric constant of about 4.5 at 0.8 eV was found whereas the calculated e(1)(0) for the bulk diamond has a value of 5.5.
|
|
| 3. |
- da Silva, A. Ferreira, et al.
(author)
-
Growth, Electrical and Optical Properties of SnO2:F on ZnO, Si and Porous Si Structures
- 2009
-
In: NANOTECH CONFERENCE & EXPO 2009, VOL 1, TECHNICAL PROCEEDINGS. - : CRC PRESS-TAYLOR & FRANCIS GROUP. - 9781439817827 ; , s. 352-
-
Conference paper (peer-reviewed)abstract
- In this work we have analyzed the optical absorption of the ZnO and SnO2:F (FTO) films and applied them in porous silicon light-emitting diodes. The absorption and energy gap were calculated by employing the projector augmented wave method [1] within the local density approximation and with a modeled on-site self-interaction-like correction potential within the LDA+U-S/C [2]. Experiment and theory show a good agreement when the optical absorption and optical energy gap are considered. A layer of FTO is deposited by spray pyrolysis on top of porous Si (PSi) or ZnO/(PSi) in order to make the LEDs. The morphology and roughness of the films are analyzed by Atomic Force Microscopy before and after the FTO deposition. The electrical and optical properties are studied by characteristics curves J x V, and electroluminescence intensity versus bias.
|
|
| 4. |
- Roman, L. S., et al.
(author)
-
Optical band-edge absorption of oxide compound SnO2
- 2006
-
In: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 252:15, s. 5361-5364
-
Journal article (peer-reviewed)abstract
- Tin oxide (SnO2) is an important oxide for efficient dielectrics, catalysis, sensor devices, electrodes and transparent conducting coating oxide technologies. SnO2 thin film is widely used in glass applications due to its low infra-red heat emissivity. In this work, the SnO2 electronic band-edge structure and optical properties are studied employing a first-principle and fully relativistic full-potential linearized augmented plane wave (FPLAPW) method within the local density approximation (LDA). The optical band-edge absorption alpha(omega) of intrinsic SnO2 is investigated experimentally by transmission spectroscopy measurements and their roughness in the light of the atomic force microscopy (AFM) measurements. The sample films were prepared by spray pyrolysis deposition method onto glass substrate considering different thickness layers. We found for SnO2 qualitatively good agreement of the calculated optical band-gap energy as well as the optical absorption with the experimental results.
|
|
